Woodpecker iLED Plus Curing Light

Unicorn Denmart Frazzer Town 3 LSC MOR Land Near J Block New Rajinder Nagar New Delhi 110060

Manufacturer/Importer warranty of 12 Months applicable for this product.
Service and Warranty are handled by the manufacturer/importer directly for this product.
PinkBlue will not be liable to replace the Products and the liability to replace any such Product is that of the Manufacturer/Importer.
PinkBlue and the Buyer acknowledge that the Products purchased/used are a subject matter of original Manufacturer/Importer’s warranties.
Any or all claims in relation to returns and replacement shall be made to the concerned Manufacturer/Importer only and not PinkBlue.
However, PinkBlue may assist the customer in lodging a complaint to get the Product replaced or serviced.
The Buyer acknowledges that the Products once sold will not be exchanged or taken back unless the seal of the package or the Product is intact.

• Dimensions: 25mm×25mm×240mm
• Net weight: 278g
• Power Input: 100V to 240V, 50Hz/60 Hz
• Wave length: 385nm-515nm
• Light intensity: 1000 mW/cm2~2500mW/cm2

• Press the mode button. The following two modes are available.
• TURBO Mode: screen shows P1, Press the time button to select the time which could be 1 or 3 seconds. Its output light intensity is about 2300 mW/cm2-2500 mW/cm2.
• NORMAL Mode: screen shows P2, Press the time button to select the time which could be 5,10,15and 20 seconds. Its output light intensity is about 1000 mW/cm2-1200 mW/cm2.
• During the operation, put the disposable sleeve on the top of the main unit, aim the top at the correct position, and press the ON/OFF button the main unit will produce a "Bi" sound, and the curing light radiates blue light and starts working according to the set modes. Meanwhile, it starts counting down and will produce a tone every 5 seconds, it stops working when counting down to "0".
• During operation, the blue light can be stopped by pressing the power button at any time.
• After a working cycle, the operator can press the ON/OFF switch to start another working cycle. Stop operating if the equipment began to heat obviously, and do not restart until the equipment cools down. Suggest continuing the working cycle less than 10 times.
• The low power detective circuit is fixed inside of the main unit, when low power is detected, the display screen of the main unit will wink, please charge in time.
• When the battery needs to be charged, connect the plug of the adapter to the AC100V~240V power supply. Then connect the output plug of the adapter to the DC 5.0V input plug of the pedestal, and then the logo turns blue. Put the main unit to the charging point of the pedestal, the display screen turns to a scrolling display, and the curing lights start charging. When charging is finished, the display screen display "1111".
• After operating, take off the disposable sleeve and throw it away, forbidden to reuse.
• This equipment will turn off automatically if don't have any action within 2 minutes, turn it on by pressing any button.
• The depth of solidification of the composite is no less than 2mm per 1 second.

• Polymerization of light-cured composite resins
• Curing of bonding agents and dental adhesives
• Suitable for use in all direct and indirect restorations
• Ideal for fast-curing bulk-fill materials in posterior teeth
• Effective in orthodontic bracket bonding procedures
• Useful in sealant and liner curing applications

• Ultra-fast 1-second curing significantly reduces chair time
• High-intensity light ensures deep and uniform polymerization
• Dual-wavelength technology cures a wide range of materials
• 360° rotatable head provides optimal access to all areas
• Ergonomic, lightweight design enhances operator comfort
• OLED display offers precise control and easy monitoring
• Multiple working modes tailored for various clinical needs
• Long-lasting battery supports high-volume dental practices

• Constant Power Output – Engineered for precise and reliable tooth restorations.

• 360° Curing Capability – Reaches all angles for complete and uniform curing.

• Ergonomic Fluid Design – Delivers superior hand comfort during prolonged use.

• Ultra-Fast Curing – Cures 2 mm of resin in just 1 second for maximum efficiency.

• Wide Spectrum Output (385–515 nm) – Ensures compatibility with a broad range of restorative materials.

• Enhanced 385–420 nm Wave Band – Perfect for curing advanced resins with TPO photoinitiators.

• Improved Compatibility with Light-Colored and Bleached Resins – The white nature of TPO enables effective curing without discoloration.

• Dual Compatibility with Photoinitiators – Efficiently cures materials using camphorquinone (peak at 460 nm) and TPO (peak at 405 nm).

• Reduces Resin Failures – Minimizes the risk of incomplete curing and resin detachment.

• Optimized for Aesthetic Restorations – Requires less camphorquinone, preserving the appearance of bleached or lighter-shade resins.

• Versatile Curing Modes – Offers both standard and wide-spectrum curing options for greater clinical flexibility.

• Upgraded Spectrum Technology – Delivers higher curing accuracy and efficiency for dependable results in every procedure.